Home > Articles > Hardware

This chapter is from the book

This chapter is from the book

Cisco Field Manual: Catalyst Switch ConfigurationCisco Field Manual: Catalyst Switch Configuration

Learn More Buy

This chapter is from the book

This chapter is from the book

Cisco Field Manual: Catalyst Switch ConfigurationCisco Field Manual: Catalyst Switch Configuration

Learn More Buy

6-4: VLAN Trunking Protocol

  • VTP sends messages between trunked switches to maintain VLANs on these switches in order to properly trunk.

  • VTP is a Cisco proprietary method of managing VLANs between switches and runs across any type of trunking mechanism.

  • VTP messages are exchanged between switches within a common VTP domain.

  • VTP domains must be defined or VTP disabled before a VLAN can be created.

  • Exchanges of VTP information can be controlled by passwords.

  • VTP manages only VLANs 2 through 1002.

  • VTP allows switches to synchronize their VLANs based on a configuration revision number.

  • Switches can operate in one of three VTP modes: server, transparent, or client.

  • VTP can prune unneeded VLANs from trunk links.

Enabling VTP for Operation

VTP exists to ensure that VLANs exist on the local VLAN database of switches in a trunked path. In addition to making sure the VLANs exist, VTP can further synchronize name settings and can be used to prune VLANs from trunk links that are destined for switches that do not have any ports active in that particular VLAN.

To manage and configure VTP, use the following steps.

  1. Activate VTP on a switch.

    1. Specify a VTP domain name:

      COS

      set vtp domain name

      IOS

      (privileged) vlan database

      (vlan_database) vtp domain name

      -OR-

      (global) vtp domain name

      By default VTP is in server mode, which is an operational mode that enables you to manage VLANs on the local switch's database and use the information in the database to synchronize with other switches. To configure VTP for operation, you must specify a name. After you enable trunking, this name propagates to switches that have not been configured with a name. If you choose to configure names on your switches, however, remember that VTP names are case-sensitive and must match exactly. Switches that have different VTP names will not exchange VLAN information.

      NOTE

      The global configuration command vtp domain is not supported on all switches that run the IOS.

      NOTE

      VTP names are used only in the context of synchronizing VTP databases. VTP domain names do not separate broadcast domains. If VLAN 20 exists on two switches trunked together with different VTP domain names, VLAN 20 is still the same broadcast domain!

    2. Enable the trunk:

      COS

      set trunk mod/port [auto | desirable | on | nonegotiate | off]

      IOS

      (global) interface type mod/port

      (interface) switchport mode dynamic [auto | desirable]

      (interface) switchport mode trunk

      (interface) switchport nonegotiate


      VTP information is passed only across trunk links. If you do not enable a trunk, VLAN information is not exchanged between the switches. See section "6-3: Trunking" for more details on trunking.

      NOTE

      Some IOS switches do not support DTP. For these switches, the only command that you can use to configure trunking is switchport mode trunk, which essentially turns trunking on.

Setting VTP Passwords

By default, there are no passwords in VTP informational updates, and any switch that has no VTP domain name will join the VTP domain when trunking is enabled. Also any switch that has the same VTP domain name configured will join and exchange VTP information. This could enable an unwanted switch in your network to manage the VLAN database on each of the switches. To prevent this from occurring, set a VTP password on the switches you want to exchange information.

  1. (Optional) Set the VTP password:

    COS

    set vtp passwd password

    IOS

    (privileged) vlan database

    (vlan_database) vtp password password

    -OR-

    (global)vtp password password

    The password is entered on each switch that will be participating in the VTP domain. The passwords are case-sensitive and must match exactly. If you want to remove the passwords, use the command set vtp passwd 0 on a COS device or no vtp password in the VLAN database mode for the IOS device.

    NOTE

    If you choose to set a password for VTP, it must be between 8 and 32 characters in length.

    The global configuration command vtp password is not supported on all switches that run the IOS.

Changing VTP Modes

VTP operates in one of three modes: server, client, and transparent. The modes determine how VTP passes information, how VLAN databases are synchronized, and whether VLANs can be managed for a given switch.

  1. (Optional) Set the VTP mode:

    COS

    set vtp mode [server | client | transparent]

    IOS

    (privileged) vlan database

    (vlan_database) vtp [server | client | transparent]

    -OR-

    (global)vtp mode [server | client | transparent]

    By default Cisco switches are in VTP server mode. For a VTP server, you can create, delete, or modify a VLAN in the local VLAN database. After you make this change, the VLAN database changes are propagated out to all other switches in server or client mode in the VTP domain. A server will also accept changes to the VLAN database from other switches in the domain. You can also run the VTP in client mode. Switches in client mode cannot create, modify, or delete VLANs in the local VLAN database. Instead, they rely on other switches in the domain to update them about new VLANs. Clients will synchronize their databases, but they will not save the VLAN information and will loose this information if they are powered off. Clients will also advertise information about their database and forward VTP information to other switches. VTP transparent mode works much like server mode in that you can create, delete, or modify VLANs in the local VLAN database. The difference is that these changes are not propagated to other switches. In addition, the local VLAN database does not accept modifications from other switches. VTP transparent mode switches forward or relay information between other server or client switches. A VTP transparent mode switch does not require a VTP domain name.

    NOTE

    The global configuration command vtp mode is not supported on all switches that run the IOS.

    As of COS 7.1(1), Cisco introduced a VTP off mode (set vtp mode off). This mode is similar to transparent mode; but in VTP off mode, the switch does not relay VTP information between switches. This command is useful when you do not want to send or forward VTP updates—for example, if you are trunking with all non-Cisco switches or if you are using Generic VLAN Registration Protocol (GVRP) dynamic VLAN creation to manage your VLAN database.

Enabling VTP Pruning

By default all the VLANs that exist on a switch are active on a trunk link. As noted in section "6-3: Trunking", you can manually remove VLANs from a trunk link and then add them later. VTP pruning allows the switch to not forward user traffic for VLANs that are not active on a remote switch. This feature dynamically prunes unneeded traffic across trunk links. If the VLAN traffic is needed at a later date, VTP will dynamically add the VLAN back to the trunk.

NOTE

Dynamic pruning removes only unneeded user traffic from the link. It does not prevent any management frames such as STP from crossing the link.

  1. (Optional) Enable VTP pruning.

    1. Enable pruning:

      COS

      set vtp pruning enable

      IOS

      (privileged) vlan database

      (vlan_database) vtp pruning

      After VTP pruning is enabled on one VTP server in the domain, all other switches in that domain will also enable VTP pruning. VTP pruning can only be enabled on switches that are VTP version 2-capable, so all switches in the domain must be version 2-capable before you enable pruning.

      NOTE

      The switch must be VTP version 2-capable, but does not have to have version 2 enabled, to turn on pruning.

    2. (Optional) Specify VLANs that are eligible for pruning:

      COS

      clear vtp pruneeligible vlanlist

      IOS

      (global) interface type mod/port

      (interface) switchport trunk pruning vlan remove vlanlist

      By default all the VLANs on the trunk are eligible for pruning. You can remove VLANs from the list of eligible VLANs using these commands. After a VLAN has been removed from the eligible list, it cannot be pruned by VTP. To add the VLANs back, use the command set vtp pruneeligible vlanlist for COS switches or switchport trunk pruning vlan add vlanlist for IOS.

Changing VTP Versions

VTP supports two versions. By default all switches are in VTP version 1 mode, but most switches can support version 2 mode.

  1. (Optional) Enable VTP version 2:

    COS

    set vtp v2 enable

    IOS

    (privileged) vlan database

    (vlan_database)vtp v2-mode

    -OR-

    (global)vtp version 2

    VTP version 2 is disabled by default. After you have enabled version 2 on one switch, all other switches in the domain also begin to operate in version 2 mode.

    NOTE

    The global configuration command vtp version 2 is not supported on all switches that run the IOS.

    VTP version 2 offers the following support options not available with version 1:

    • Unrecognized type-length-value (TLV) support—A VTP server or client propagates configuration changes to its other trunks, even for TLVs it is not able to parse. The unrecognized TLV is saved in NVRAM.

    • Version-dependent transparent mode—In VTP version 1, a VTP transparent switch inspects VTP messages for the domain name and version and forwards a message only if the version and domain name match. Because only one domain is supported in the Supervisor engine software, VTP version 2 forwards VTP messages in transparent mode, without checking the version.

    • Consistency checks—In VTP version 2, VLAN consistency checks (such as VLAN names and values) are performed only when you enter new information through the command-line interface (CLI) or Simple Network Management Protocol (SNMP). Consistency checks are not performed when new information is obtained from a VTP message or when information is read from NVRAM. If the digest on a received VTP message is correct, its information is accepted without consistency checks.

Verifying VTP Operation

After configuring VTP, use one of the following commands to verify the VLAN port assignments:

COS

show vtp domain

IOS

(privileged) show vtp status

Feature Example

In this example, Access_1, Distribution_1, and Distribution_2 will be assigned to a VTP domain named GO-CATS. Figure 6-3 shows that Access_1 will be in VTP client mode with an 802.1Q trunk connecting to Distribution_1. Distribution_1 will be configured in VTP server mode with an ISL trunk connecting it to Core_1, which is in VTP transparent mode. Core_1 has an ISL trunk to Distribution_2, which is also in VTP server mode. VTP pruning has also been enabled for the domain, and all switches are configured so that VLAN 10 is not prune-eligible on the trunk links. Because VTP runs across trunk links, it is not necessary to configure the VTP domain name on the Distribution_2 switch or the Access_1 switch. It is also not necessary to configure the pruning on each switch; this is also propagated by VTP.

Figure 6-3Figure 6-3 Network Diagram for VTP Configuration on Access_1, Distribution_1, Distribution_2, and Core_1.

An example of the Catalyst OS configuration for Core_1 follows:

Core_1 (enable)>set vtp mode transparent
Core_1 (enable)>set trunk 1/1 on isl
Core_1 (enable)>set trunk 1/2 on isl
Core_1 (enable)>

An example of the Catalyst OS configuration for Distribution_1 follows:

Distribution_1 (enable)>set vtp domain GO-CATS
Distribution_1 (enable)>set trunk 1/1 on isl
Distribution_1 (enable)>set trunk 2/1 on dot1Q
Distribution_1 (enable)>set vtp pruning enable
Distribution_1 (enable)>clear vtp pruneeligible 10

An example of the Catalyst OS configuration for Distribution_2 follows:

Distribution_2 (enable)>set trunk 1/1 on isl
Distribution_2 (enable)>clear vtp pruneeligible 10

An example of the Layer 2 IOS configuration for Access_1 follows:

Access_1#vlan database
Access_1 (vlan)#vtp client
Access_1 (vlan)#exit
Access_1 #config t
Access_1 (config)#interface gigabitethernet 0/1
Access_1 (config-if)#switchport mode trunk
Access_1 (config-if)#switchport trunk encapsulation dot1Q
Access_1 (config-if)#switchport trunk pruning vlan remove 10
Access_1 (config-if)#end
Access_1#copy running-config startup-config

InformIT Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from InformIT and its family of brands. I can unsubscribe at any time.

Overview


Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information


To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites, develop new products and services, conduct educational research and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@informit.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information


Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security


Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children


This site is not directed to children under the age of 13.

Marketing


Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information


If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out


Users can always make an informed choice as to whether they should proceed with certain services offered by InformIT. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.informit.com/u.aspx.

Sale of Personal Information


Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents


California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure


Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links


This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact


Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice


We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020